多重短程有序准化学模型: 有序原子对的对立与统一

在准化学模型框架下, 假设有序原子对同时具有可区分与不可区分的双重属性, 首先构造了双重短程有序准化学模型, 然后讨论了该模型所能满足的各类理论极限. 经总结提炼, 提出了有序原子对的对立统一理论. 基于该理论, 进一步将双重短程有序准化学模型做了一般化推广, 开发了多重短程有序准化学模型. 该模型能够有效描述二元熔体中存在多重短程有序构型时的热力学行为. 选取了至少存在两重短程有序构型的Bi-K熔体来检验模型的合理性和可靠性. 结果表明, 除配位数外, 只需4个模型参数就能合理再现该二元熔体所有的热化学数据.     

Effects of ball-to-powder diameter ratio and powder particle shape on EDEM simulation in a planetary ball mill

The effects of the ball-to-powder diameter ratio (BPDR) and the shape of the powder particles on EDEM simulation results and time in the planetary ball mill was investigated. BPDR was varied from 1 to 40/3 by changing the powder particle diameter from 8 to 0.6 ?mm. The size and shape of the powder particles do not give a significant change in both the ball motion pattern and simulation results when BPDR is over 20/3. It can be assumed that the kinetic energy of the ball has nothing to do with the size and shape of the powder particle. The simulation time and data size increase exponentially as BPDR increases. The effect of change of the powder particle shape on the calculated data size is not significant, but the more complicated its shape, the longer the simulation time, which is linearly related to the number of spheres composing a particle.     

The Shackling Effect in Cyclic Azobenzene Liquid Crystal

We demonstrate here a novel method for the design of liquid crystals (LCs) via the cyclization of mesogens by flexible chains. For two azobenzene-4,4′-dicarboxylate derivatives, the cyclic dimer, cyclic bis(tetraethylene glycol azobenzene-4,4′-dicarboxylate) (CBTAD), shows LC properties with smectic A phase, while its linear counterpart, bis(2-(2′-hydroxyethyloxy)ethyl azobenzene-4,4′-dicarboxylate (BHAD), has no LC phase. The difference is ascribed to the shackling effect from the cyclic topology, which leads to the much smaller entropy change during phase transitions and increases the isotropic temperature greatly for cyclics. In addition, the trans-to-cis isomerization of azobenzene groups under UV-light is also limited in CBTAD. With the reversible isomerization of azobenzene groups, CBTAD showed interesting isothermal phase transition behaviors, where the LC phase disappeared upon photoirradiation of 365 nm UV-light, and recovered when the UV-light was off. Combined with the smectic LC nature, a novel UV-light tuned visible light regulator was designed, by simply placing CBTAD in two glass plates. The scattered phase of smectic LC was utilized as the “OFF” state for light passage, while the UV-light induced isotropic phase was utilized as the “ON” state. The shackling effect outlined here should be applicable for the design of cyclic LC oligomers/polymers with special properties.

     

Phenylethynyl-terminated Imide Oligomers Modified by Reactive Diluent for Resin Transfer Molding Application

To meet the processing requirements of resin transfer moulding(RTM)technology,reactive diluent containing m-phenylene moiety was synthesized to physically mixed with phenylethynyl terminated cooligoimides with well-designed molecular weights of 1500-2500 g/mol derived from 4,4’-(hexafluoroisopropylidene)diphthalic anhydride(6 FDA),3,4’-oxydianiline(3,4’-ODA)and m-phenylenediamine(m-PDA).This blend shows low minimum melting viscosity(<1 Pa·s)and enlarged processing temperature window(260–361℃).FPI-R-1 stays below 1 Pa·s for2 h at 270℃.The relationship between the molecular weight of the blend and its melting stability was first explored.Blending oligoimides with lower molecular weights exhibit better melting stability.Upon curing at 380℃for 2 h,the thermosetting polyimide resin demonstrates superior heat resistance(T_g=420-426℃).     

基于废旧锂电池回收制备LixMO (x=0.79, 0.30, 0.08; M=Ni/Co/Mn)材料作为锂-氧气电池正极催化剂的电化学性能研究

锂-氧气电池因其超高的理论比容量而受到科研界的广泛关注, 但其存在较为严重的充放电极化和较差的循环稳定性等问题, 从而极大地限制其商业化进程. 因此设计出有效的正极催化剂是解决锂-氧气电池面临的这些棘手问题的必要手段. 通过对不同充电状态的废旧锂电池正极进行回收制得三种不同锂含量的多元金属氧化物Li_xMO (x=0.79, 0.30, 0.08; M=Ni/Co/Mn), 并分别用作锂-氧气电池正极催化剂. 系统研究了Li_xMO材料中锂含量及晶体结构对其电化学性能的影响. 电化学测试结果表明, 与Li_0.79MO和Li_0.08MO催化剂相比, 基于Li_0.30MO为正极催化剂的锂-氧气电池在电流密度100 mA•g^–1和限定容量800 mAh•g^–1的条件下具有较高的放电比容量(14655.9 mAh•g^–1)、较低的充电电压(3.83 V)和较高的能量转换效率(72.2%). 而且该电池体系在充放电循环140圈后充电终止电压仍低于4.3 V. 最终认为制得的Li_0.30MO材料具有优异的催化性能归因于其稳定的层状-岩盐相复合结构以及结构中富含的氧化镍相和氧空位之间的协同作用. 这些优点能够促进放电产物的可逆形成与分解, 从而提高锂-氧气电池循环性能.     

A novel approach to synthesize dichlorobenzonitriles by selective ammoxidation

Research on Chemical Intermediates - Dichlorobenzonitriles are important organic intermediates for the production of many fine chemicals and are produced most economically and environment-friendly...     

The new synthesis of sulfuryl-bridged triazinane and its selective recognition to SO42−

Research on Chemical Intermediates - A new method has been developed for the synthesis of a cage-like sulfuryl-bridged triazinane molecule HEXS by acidic condensation of a glycoluril analog with...     

Insight into the Excellent Tribological Performance of Highly Oriented Poly(phenylene sulfide)

Achieving low friction and wear of poly(phenylene sulfide)(PPS) without using fillers or blending is a challenging task, but one of considerable practical importance. Here we describe how neat PPS with high tribological performance is achieved by manipulating processing parameters(pressure, flow and temperature). The key to achieving high tribological performance is comparatively high molecular chain orientation, realized in neat PPS, at high shear rates and low pressure. The friction coefficient and wear rate are as low as ~0.3 and~10^-6 mm³·N^-1·m^-1, respectively, which break the record for neat PPS. These values are even better than those for PPS-based blends and comparable to PPS composites. Further studies show, for the first time, that wear rate decreases exponentially with increasing molecular chain orientation, prompting us to revise the classical Archard's law by including the effect of molecular chain orientation. These findings open the possibility of using neat PPS in highly demanding tribological applications.     

基于BiOCl-Fe2O3@TiO2介孔复合材料的光电化学合成氨性能研究

传统合成氨工艺存在能耗高、污染严重的问题. 因此, 高效、低能耗绿色合成氨工艺的开发迫在眉睫. 光电化学以H₂O和N₂为原料, 可以在太阳光驱动下, 在常温常压条件下实现氨的合成, 因而受到广泛重视. 但总的来说, 效率和产率都达不到实际要求. 新型高效催化剂及工艺的开发是提高合成氨产率及效率的关键. 非贵金属催化剂具备成本低、来源广泛、可操作性强的优势, 有利于光电化学合成氨的产业化. 本实验采用溶胶凝胶结合原位热裂解的方法制备了分散性好、结构均匀的BiOCl-Fe₂O₃@TiO₂复合材料, 对其物相、微观结构、表面状态、光学性能、电学性能等方面进行了系统表征, 并探究了该材料在常温常压下光电化学合成氨的催化活性. 结果表明, 同纯介孔TiO₂相比_, BiOCl-Fe₂O₃@TiO₂的吸收带隙变窄, 可见光吸收能力增强, 光生载流子的利用率增加, 光电合成氨的产率提升了7倍, 且BiOCl-Fe₂O₃@TiO₂显示了优异的化学稳定性. 本研究工作为绿色合成氨催化材料及工艺设计提供了新思路.